If you wish to contribute or participate in the discussions about articles you are invited to contact the Editor

Antennas: Difference between revisions

From Navipedia
Jump to navigation Jump to search
m (Included editor logo.)
 
(24 intermediate revisions by 4 users not shown)
Line 1: Line 1:
{{Article Infobox2
{{Article Infobox2
|Category=Receivers
|Category=Receivers
|Title={{PAGENAME}}
|Editors=GMV
|Authors=GMV
|Level=Advanced
|Level=Advanced
|YearOfPublication=2011
|YearOfPublication=2011
|Logo=GMV
|Logo=GMV
|Title={{PAGENAME}}
}}
}}
From a user perspective, antennas are the main interface between the GNSS Space Segment (the satellite constellations) and the User Segment (GNSS receivers), as they are responsible for capturing the [[GNSS signal|L-band signals]] transmitted from space. Antennas requirements can range from gain vs. azimuth and elevation, multipath and interference rejection, or stability of the electrical phase centre, to size, shape and environmental constraints.


From a user prespective, antennas are the main interface between the GNSS Space Segment (the satellite constellations) and the User Segment (GNSS receivers), as they are responsible for capturing the [[GNSS signal|L-band signals]] transmitted from space. Antennas requirements can range from gain vs. azimuth and elevation, mutipath and interference rejection, or stability of the electrical phase center, to size, shape and environmental constraints. Due to the characteristics of GNSS systems, receiver antennas are typicaly Right-Hand Circularly Polarized<ref>[[wikipedia:Circular Polarization]]</ref> (RHCP) antennas, and the spacial reception pattern is near hemispherical: this configuration enables user reception of satellite signals in any azimuthal direction, and from zenith to horizon, thus maximizing satellite visibility.
Typically, the antennas used in GNSS receivers are formed by a ''radiating element'', mounted on a ''ground plane'', followed by an ''amplifier'' and protected by a ''radome'':
*<b>the radiating element</b> is responsible for the antenna bandwidth and radiating characteristics,
*<b>the ground plane</b> conditions the radiation pattern shape, foremost at low elevation angles,
*<b>the amplifier</b> sets the receiver noise figure,  
*<b>the radome</b> affects the phase centre.


==Antenna types==
Due to the characteristics of GNSS systems, receiver antennas are typically Right-Hand Circularly Polarized<ref>[[wikipedia:Circular Polarization]]</ref> (RHCP) antennas, and the spacial reception pattern is near hemispherical: this configuration enables user reception of satellite signals in any azimuthal direction, and from zenith to horizon, thus maximizing satellite visibility.
 
==Antenna configurations==
Different applications may require different types of antenna design, technology and location<ref>[[wikipedia:Category:Radio frequency antenna types]]</ref>. In fact, as show in Figure 1, antennas can range from large roof-mounted antennas (e.g. for a static open sky view) to embedded antennas in receiver boards (e.g. for mobile handheld devices).
Different applications may require different types of antenna design, technology and location<ref>[[wikipedia:Category:Radio frequency antenna types]]</ref>. In fact, as show in Figure 1, antennas can range from large roof-mounted antennas (e.g. for a static open sky view) to embedded antennas in receiver boards (e.g. for mobile handheld devices).


[[File:GNSS_antennas.png|right|thumb|320px|'''''Figure 1:''''' Examples of GNSS antenna types: rooftop Dome (left),  embedded Patch (top-right), Choke Ring design (bottom-right).]]
The most common types of antennas in terms of ''implementation'' of antenna elements, ground planes, are:
The most common types in terms of ''implementation'' are:
[[File:GNSS_antennas.png|right|thumb|260px|'''''Figure 1:''''' Examples of GNSS antenna types: rooftop Radome (left),  embedded Patch (top-right), Choke Ring design (bottom-right).]]
[[File:Ground_Station_Fucino_(ESA).jpg|right|thumb|260px|'''''Figure 2:''''' View of the antennas at Galileo Control Centre in Fucino, Italy (Contents ESA).]]


*'''Patch Antennas''': Patch antennas are the most common antenna type, as they are used in handheld mobile devices such as portable navigation devices and smartphones. The antenna is buit as a low-profile thin microstrip (i.e. patch), suitable for small form-factor devices.
*'''Patch Antennas''': Patch antennas are often used in [[Handheld Outdoor Receivers|handheld mobile devices]], such as Portable Navigation Devices (PND) or smartphones, since the antenna is built as a low-profile thin microstrip (i.e. patch), suitable for small form-factor devices. Microstrip patches or aperture-coupled patches can be single frequency or dual frequency, but also broadband. Patches are not circularly polarized by nature, so they achieve circular polarization by quadrature excitation of two linearly polarized ports. The quality of the circular polarization depends largely on the feeding network and may be sensitive to fabrication issues, and the crosspolarization near the horizon tends to be high. They provide an excellent form factor (size and weight), and are used in most [[Aviation Applications|aviation]] GNSS antennas satisfying ARINC 743<ref>https://www.arinc.com/cf/store/catalog_detail.cfm?item_id=329</ref> standard.


*'''Dome Antennas''': As the name suggests, dome antennas are housed in a hemispherical-like dome, and are seen in several roof-mounted installations.
*'''Turnstile Antennas''': The turnstile antenna consists of two dipoles fed in 90° phase. A horizontal turnstile antenna in free space is vertically polarized in its plane, and has opposite circular polarizations above and below. Therefore the antenna requires  a ground plane for geodetic applications. When combined with a choke ring ground plane, it is a very common element in geodetic applications.


*'''Helical Antennas''': Helical antennas are typicaly built as a conducting wire around a cilindrical core, in a helix form, down to a ground plane. In GNSS receivers, the helix antennas can be used as directional antennas, with a radiation pattern along the axis of the antenna.
*'''Helical Antennas''': Helical antennas are typically built as a conducting wire around a cylindrical or conical core, in a helix form, and can be used with or without a ground plane, depending on the configuration. In GNSS receivers, the helix antennas can be used as directional antennas, with a radiation pattern along the axis of the antenna.


*'''Choke Ring Antennas''': A choke ring antenna design consists in sorrounding a central antenna with several concentric conductive rings, enclosed in a protective dome. Its design is notable for the ability to reject multipath and low elevation signals (including reflections on the ground).
*'''Spiral Antennas''': The equiangular planar spiral is one of the prototypical "frequency-independent" antennas, so it offers excellent bandwidth. The antenna is circularly polarized by nature, although the quality of the polarization may depend on the feeding arrangement. Since the basic element radiates equally in both hemispheres, a ground plane of some kind is required.


*'''Phased-Array Antennas''': Phased-array antennas are mostly used for military or high-end applications, and consist of numerous antenna elements arranged in an array pattern. Each signal from an antenna in the array can be processed by introducing dynamic phase shifts, and when the outputs of the array are summed, the effective radiation pattern can be maximized in some directions and nulled in other (e.g. to insert nulls in the antenna pattern to adjust to jamming threats).
*'''Radome Antennas''': As the name suggests, in this configuration the antenna elements are housed in a hemispherical-like dome (the radome). Radomes are usually added to protect the antenna when the site where it is installed demands it (e.g. in roof-mounted installations) due to weather conditions, antenna security, or wildlife concerns. Typically, hemispherical radomes are used, because they have little effect on the phase centre stability and symmetry, and non-hemispherical radomes are usually avoided, except when the shape is required by site characteristics (e.g. conical radomes for snow rejection). Antenna phase centre calibration should be performed with the radome.


*'''Parabolic Antennas''': Resembling popular TV and communications satellite dish antennas, parabolic antennas use a parabolic reflecting surface to direct the radio waves. The parabolic antenna is highly directive, so RF signals comming from the satellites can be received from one particular direction only. Its directive build structure and high gain make this type of antenna suitable for Ground Segment stations, such as monitoring or uplink stations.
*'''Choke Ring Antennas''': A choke ring antenna design consists in surrounding a central antenna element with several concentric conductive rings, enclosed in a protective dome. Its design is notable for the ability to reject multipath and low elevation signals (including reflections on the ground). Choke Ring antennas reflects signals that come from below, and draw surface wave signals into the choke channels, where they are cancelled or reflected away from the receiving element.


An alterantive distinction of GNSS antennas<ref>http://www.gpsworld.com/gnss-system/receiver-design/innovation-gnss-antennas-8480</ref>, in terms of ''application'', is:
*'''Resistive Plane Antennas''': The resistive plane antenna uses electrical resistance (rather than frequency-tuned rings as Choke Ring antennas) to keep unwanted signals from reaching the antenna element. Signals that strike the plane lose all energy before they reach the element and cause interference. Resistive Plane antennas provide similar performances as Choke Ring antennas, but with less weight and cost.


*'''Geodetic Antennas''': Survey and geodetic applications typicaly require fixed high-accuracy receivers and antennas, so it is common for multi-frequency / multi-constelaltion choke-ring antennas to be used for best performance.
*'''Phased-Array Antennas''': Phased-array antennas are mostly used for military or high-end applications, and consist of numerous antenna elements arranged in an array pattern. Each signal from an antenna in the array can be processed by introducing dynamic phase shifts, and when the outputs of the array are summed, the effective radiation pattern can be maximized in some directions and nulled in other (e.g. inserting nulls in the antenna pattern can help adjusting to jamming threats). Furthermore, beam steering techniques can be used to increase dynamically the antenna gain in a given direction, e.g. of a given satellite. This technique can be used in ground reference antennas in order to maximize the antenna gain.


*'''Rover Antennas''': Rover antennas are used in land survey, forestry, construction, and other portable or mobile applications, and represent a good trade-off between accuracy and portability. Due to the need for mobility, the antenna is usually mounted on a handheld pole, stand or tripod: nevertheless, due to size and weight constraints, choke ring antennas are not a good solution for rover applications, so a high-end alternative must be found to ensure the necessary accuracy.
*'''Parabolic Antennas''': Resembling popular TV and communications satellite dish antennas, parabolic antennas use a parabolic reflecting surface to direct the radio waves. The parabolic antenna is highly directive, so RF signals coming from the satellites can be received from one particular direction only. Its directive build structure and high gain make this type of antenna suitable for Ground Segment stations, such as monitoring or uplink stations, as shown in Figure 2.


*'''Handheld Receiver Antennas''': These antennas are found in most current smatphones and portable navigation devices,  and are chosen for size, cost and power consumption constraints. Usualy single-frequency antennas, they are available in a range of implementations such as helical or patch antennas, both passive and active (see section below for details).
==Applications==
An alternative distinction of GNSS antennas<ref>[http://www.nxtbook.com/nxtbooks/questex/gps0209/index.php?startid=46#/42 GPS World 2009 Antenna Survey.]</ref> is in terms of the envisaged ''application'':


==Characteristics==
*'''Geodetic Antennas''': Survey and geodetic applications typically require fixed high-accuracy receivers and antennas, so it is common for multi-frequency / multi-constellation choke-ring antennas to be used for best performance.
[[File:Patch_antenna_pattern.gif|right|thumb|320px|'''''Figure 2:''''' Example of a patch antenna pattern.]]
Antennas used in GNSS receivers are targeted at capturing L-band signals originating from satellite constellations, so care must be taken when matching design specifications in terms of signal bandwidth, center frequency, desired response, transfer function, and electromechanical factors.


Typical '''radiation pattern''' coverage is around 160º, resulting in low gain for signals comming in at low elevation angles, as shown in Figure 2 for a patch antenna. This pattern aims at maximizing the gain at zenith, decreasing to near unity at an elevation angle of around 10º-15º, and to negative gains below the elevation threshold (sometimes refered to as '''elevation mask'''). At zenith, the ratio of the vertical electric field to the horizontal electric field response is near unity, and this ratio is referred to as the '''axial ratio'''<ref>For further details, see <i>Kaplan, E.D. et al, "Understanding GPS: Principles and Applications", second edition, chapter 3, section 3.4.1.1</i>.</ref>.
*'''Rover Antennas''': Rover antennas are typically used in land survey, forestry, construction, and other portable or mobile applications, hence they require a trade-off between accuracy and portability. Due to the need for mobility, the antenna is usually mounted on a handheld pole, stand or tripod. In general, due to size and weight constraints, choke ring antennas are not a good solution for rover applications, so higher phase center variations are often seen in rover antennas.  


Another important design factor for antennas is the '''phase center'''. In fact, when a receiver determines a position solution, it is actualy estimating the position of the electrical phase center of the antenna, where the signals are captured, regardless of the distance from the antenna the receiver device actualy is. This ''electrical'' phase center should not be mistaken with the ''physical'' phase center: although the latter can be observed and is a physical constant, the first may vary, depending on the direction of arrival of the received signal.
*'''Handheld Receiver Antennas''': These antennas are found in most current smartphones and portable navigation devices, and the key design drivers are size, cost and power consumption constraints. Usually single-frequency antennas, they are available in a range of implementations such as helical or patch antennas, both passive and active (see section below for details).


In general, GNSS antennas don't need any electrical power to operate, and are refered to as '''passive antennas'''. Typical scenarios for passive antennas are mobile devices, where power consumption is a critical issue. However, passive antennas must connect to the receiver's [[Front End|front end]] with very low losses, since there is no amplification mechanism involved at signal reception. In applications in which the antenna can be away from the receiver (e.g. rooftop antennas), signal amplification can be implemented in the antenna itself, and for that fact they are called '''active antennas'''. Their purpose is to amplify the received signal to compensate for potential losses in long coaxial cables, at the cost of a higher power consumption (power is usually delivered from the front end through the coaxial cable itself). In this approach, a Low-Noise Amplifier (LNA) is usualy added to the antenna setup, in order to ensure a low noise figure in the signals to process. An example of active antenna use is for indoor reradiating purposes, where an active antenna inside a building reradiates the signals comming from another antenna, placed outside the building.
==Characteristics==
 
Antennas used in GNSS receivers aim at capturing L-band signals and therefore their design should take into account signal bandwidth, centre frequency, desired response, transfer function, multipath mitigation, and electromechanical factors. Table 1 shows a few relations between antenna applications and characteristics.
[[File:Ground_Station_Fucino_(ESA).jpg|right|thumb|400px|'''''Figure 3:''''' View of the antennas at Galileo Control Centre in Fucino, Italy (Contents ESA).]]
Besides electrical considerations, GNSS antennas must also take into account the signal structure in terms of RF spectrum and '''bandwidth''', and should be selected not only in accordance with the front end specifications, but also with the envisaged usage and application. New constellations and modulations brind different [[GNSS signal|spectrum allocations and bandwiths]] (see each constellation's [[Main_Page|articles]] for specifications on spectrum allocation and bandwidth). As an example, Table 1 ilustrates GPS L1 and Galileo E1 bands (which share the same center frequency), and shows several parameters related to the bandwidths of incoming signals.




{| class="wikitable" align="center" style="text-align: center;"
{| class="wikitable" align="center" style="text-align: center;"
|+ align="bottom" | '''''Table 1:''''' GPS and Galileo L1/E1 civil signal bandwidth characteristics.
|+ align="bottom" | '''''Table 1:''''' GNSS antenna applications and characteristics.
|-
! &nbsp; || Geodetic || Rover || Handheld
|-
! Frequency Bands
| Single to multiband || Single to multiband || Singleband
|-
|-
! &nbsp; || GPS L1 C/A (BPSK) || Galileo E1 B/C (BOC) || Galileo E1 B/C (CBOC)
! Bandwidth
| Broadband || Narrow to Broadband || Narrowband
|-
|-
! Chip Rate [Mcps]
! Radiation Pattern
| 1.023 || 1.023 || 1.023 / 6.138
| Controlled || Controlled || Not controlled
|-
|-
! Primary Code Length [chips]
! Multipath suppression
| 1023 || 4092 || 4092
| High || Medium || None
|-
|-
! Primary Code length [ms]
! Sensitivity
| 1 || 4 || 4
| High || Medium to high || Low
|-
|-
! Symbol Rate [sps]
! Interference Handling
| 50 || 250 || 250
| High rejection || Good rejection || Minimal rejection
|-
|-
! Centre Frequency [MHz]
! Phase centre
| colspan="3" | 1575.42
| Very important || Important || Not important
|-
|-
! Receiver Reference Bandwidth [MHz]
! Dimensions
| 4.092 || 8.184 || 24.552
| Large || Portable || Very small
|-
! Weight
| Heavy || Portable || Lightweight
|-
!Cost
| High || Medium || Low
|}
|}




Typically, the bandwidth of a GPS patch or helix antenna ranges from 1% to 2% of the center frequency. Two percent bandwidths for L1, L2, and
===Antenna Power===
L5 center frequencies are 31.5 MHz, 24.6 MHz, and 23.5 MHz, respectively. GPS
In general, GNSS antennas do not need any electrical power to operate, and are referred to as '''passive antennas'''. Typical scenarios for passive antennas are mobile devices, where power consumption is a critical issue. However, passive antennas must connect to the receiver's [[Front End|front end]] with very low losses, since there is no amplification mechanism involved at signal reception.
receivers that track P(Y) code on both L1 and L2 need to accommodate on the order
 
of 20.46-MHz bandwidths on both frequencies. If the set only tracks C/A code or
In applications in which the antenna can be away from the receiver (e.g. rooftop antennas), signal amplification can be implemented in the antenna itself, and for that fact they are called '''active antennas'''. Their purpose is to amplify the received signal to compensate for potential losses in long coaxial cables, at the cost of higher power consumption (power is usually delivered from the front end through the coaxial cable itself). In this approach, a Low-Noise Amplifier (LNA) is usually added to the antenna setup, in order to ensure a low noise figure in the signals to process. An example of active antenna use is for indoor reradiating purposes, where an active antenna inside a building reradiates the signals coming from another antenna, placed outside the building.
L1C on L1, the antenna (and receiver) need to accommodate bandwidths of
 
approximately 2.046 and 4.092 MHz, respectively. It should be noted that the
===Radiation Pattern===
receiver’s antenna/front-end bandwidth is directly proportional to the accuracy
[[File:Patch_antenna_pattern.gif|right|thumb|260px|'''''Figure 3:''''' Example of a patch antenna pattern.]]
required for the specific application of the receiver. That is, the more frequency content
GNSS signals use Right Hand Circular Polarization (RHCP), but antennas are not perfect, so a RHCP antenna will pick up some Left Hand Circular Polarization (LHCP) energy as well. In radiation terms, RHCP is referred to as the ''co-polar component'', and LHCP is referred as the ''cross-polar component''. The typical '''radiation pattern''' coverage is around 160º, resulting in low gain for signals coming in at low elevation angles, as shown in Figure 3 for a patch antenna. This pattern aims at maximizing the gain at zenith, decreasing to near unity at an elevation angle of around 10º-15º, and to negative gains below the elevation threshold (sometimes referred to as '''elevation mask''').
of the received satellite signal that is processed, the better the accuracy performance
 
will be. For example, a survey receiver antenna/front end will most likely be
Real-world GNSS antennas experience a gain roll-off of 10 to 20 dB from broadside (90º elevation) to the horizon (0º elevation). At zenith, the ratio of the vertical electric field to the horizontal electric field response is near unity (0 dB); this ratio is referred to as the '''axial ratio'''<ref>Kaplan, E.D. et al,<i>"Understanding GPS: Principles and Applications"</i>, second edition, chapter 3, section 3.4.1.1.</ref> (AR). The AR tends to degrade towards lower elevations, and it can reach less than 3 to 6 dB at 10° elevation for a high-performance antenna.
designed to pass the full 20.46 MHz of the P(Y) code. Whereas, a low-cost hiking
 
receiver designed for C/A code may only have a front-end bandwidth of 1.7 MHz
===Multipath===
instead of the full 2.046 MHz. (Further elaboration on bandwidth and accuracy
Signals sent from GNSS satellites will directly arrive at the antenna but they also may be reflected off the ground, buildings or other obstacles, arriving at the antenna multiple times and delayed in time. This phenomenon is called '''multipath''', and since it degrades position accuracy, it should be avoided or reduced. Multipath signals can basically come from three directions: the ground, hitting the ''back of the antenna'', the ground or an object, hitting the antenna at a ''low elevation'', or an object, hitting the antenna at a ''high elevation''.
performance is contained in Chapter 5.)
 
For example, those utilizing L1 C/A code and L2C will need a
In specular reflections, the reflected signal may change its polarization with respect to the original one, i.e. depending on the material and on the angle of incidence, a RHCP signal can be reflected as a LHCP signal. The multipath susceptibility of an antenna can then be quantified, with respect to the antenna’s radiation pattern characteristics, by the multipath ratio (MPR). The multipath ratio is computed as the ratio between the RHCP gain at the satellite signal incident angle with respect to the sum of the RHCP and LHCP gains at the multipath signal incident angle.
dual-band antenna. (Dual frequency measurements enable determination of the ionospheric delay and provide robustness to interference. Ionospheric delay determination
 
and compensation are discussed in Chapter 7.) SOL signal users that require operation in the ARNS bands will need antennas to receive C/A code on L1 and the
Gain roll-off towards the lower elevations helps suppressing multipath signals: however, a good AR is always a must, since gain roll-off alone is insufficient.
L5 signal on L5.
 
===Phase Centre===
Another important design factor for antennas is the '''phase centre'''. In fact, when a receiver determines a position solution, it is actually estimating the position of the electrical phase centre of the antenna, where the signals are captured, regardless of the distance from the antenna the receiver device really is. This ''electrical'' phase centre should not be mistaken with the ''physical'' phase centre: although the latter can be observed and is a physical constant, the first may vary, depending on the direction of the signal arrival.
 
Determining the phase centre is important in GNSS systems, particularly when millimeter positioning resolution is desired; nevertheless, for well-designed high-end GNSS antennas, phase centre variations in azimuth are small and in the order of few millimetres (the vertical phase offsets are typically 10 mm or less). See the articles on [[Antenna Phase Centre|antenna phase centre]] and [[Receiver Antenna Phase Centre|receiver antenna phase centre]] for more details.
 
===Interference Handling===
An out-of-band interferer is an RF source outside of the GNSS frequency bands, which can drive the LNA into its nonlinear range, and the LNA starts to operate as a multiplier or comb generator. RF filters can reduce the out-of-band signals by tens of dBs, which is enough in most cases. Of course, filters add insertion loss, amplitude and phase ripple, all of which degrade receiver performance. In-band interferers can be the third-order mixing products, or simply an RF source that transmits inside the GNSS bands. If these are relatively weak, the receiver will handle them; from a certain power level on, however, commercial receivers can do nothing about them.
 
Furthermore, antenna arrays can use beamforming techniques<ref>A. Konovaltsev, F. Antreich, A. Hornbostel (2007), <i>“Performance assessment of antenna array algorithms for multipath and interferers mitigation”</i>, Proc. of 2nd Workshop on GNSS Signals & Signal Processing (GNSS SIGNALS’2007), 24-25 April 2007, Noordwijk, the Netherlands.</ref> to create nulls in the radiation pattern in the direction of a-priori known interferers – this technique is often used in military applications.
 
===Noise and Out of Band Rejection===
The signals received by the antenna are very weak. For instance, in GPS, the minimum received power is –158.5 dBW (for L1) and –164.5 dBW (for L2), for signals arriving at 5º elevation. Furthermore, the cable and the receiver elements generate noise that can affect the signal. To avoid reducing this effect, the first element following the antenna is usually a Low Noise Amplifier (LNA), so that the power of the GNSS signal is greater than the noise generated by the cable and the receiver elements.
 
Adding the fact that Out of Band signals need to be rejected or attenuated to prevent the saturation of the amplifiers, and that the antenna does not provide a good close Out of Band rejection, a pass band filter can be placed before the first amplifier. This operation, however, will degrade the Noise Figure, so there is a trade-off in the design of the antenna LNA between the Noise Figure and the Out of Band Rejection. Typically, the compromise is reached by distributing the filtering across the LNA in two stages.
 
===Signal Bandwidth===
Besides electrical considerations, GNSS RF section must also take into account the signal structure in terms of RF spectrum and bandwidth, and should be selected not only in accordance with the front end specifications, but also with the envisaged usage and application.  
Typical GPS antennas are able to process signal bandwidth of around 1% to 2% of the signal center frequency (yielding over 20 MHz bandwidth in L1). These values are able to fit most GNSS signals and therefore the limitations on the signal bandwidth is usually concentrated in the [[Front End|front-end]] block, keeping in mind that both antenna and front-end blocks contribute to this bandwidth<ref>Kaplan, E.D. et al, <i>"Understanding GPS: Principles and Applications"</i>, second edition</ref>.
 
===Front end connection===
The antenna signal provided to the front end is received as a low-power signal, and is typically amplified and filtered before entering the down-conversion and sampling process. In the case of the antenna being far from the receiver, for physical constraints or application necessity, special attention should be drawn to the choice of the connecting cable.
 
 
{| class="wikitable" align="center" style="text-align: center;float: right"
|+ align="bottom" | '''''Table 3:''''' Example of coaxial cable types and losses [dB / 100m].
|-
! &nbsp; || 915 MHz || 1.2 GHz || 2.4 GHz
|-
! RG-58
| 54.1 || 69.2 || 105.6
|-
! RG-8X
| 42.0 || 52.8 || 75.8
|-
! LMR-400
| 12.8 || 15.7 || 22.3
|-
! LMR-600
| 8.2 || 10.2 || 14.4
|-
! 1 5/8" LDF
| 2.5 || 3.1 || 4.6
|}
 


==Front end connection==
Coaxial cables are built in many different ways, with different materials, with or without special shielding, and specify losses in units of power and length per frequency range - typical values are in the form of "''X'' dB/100 m @ ''Y'' MHz". Requirements like cable length, impedance, antenna gain and power supply (for the case of active antennas) need to be taken into account to minimize signal losses. For illustrative purposes, an example of the loss ranges at stake<ref>http://www.w4rp.com/ref/coax.html</ref> is shown in Table 3. In this example, from a signal loss point of view, the "''1 5/8" LDF''" cable would have less losses in the 1.2 - 1.6 GHz range of GNSS signals, and should be considered for connecting an antenna to the front end.


==Related articles==
==Related articles==
Line 100: Line 161:
*[[Receiver Types]]
*[[Receiver Types]]
*[[System Design Details]]
*[[System Design Details]]
*[[Front End]]
*[[Receiver Characteristics]]


==References==
==References==

Latest revision as of 16:33, 18 September 2014


ReceiversReceivers
Title Antennas
Edited by GMV
Level Advanced
Year of Publication 2011
Logo GMV.png

From a user perspective, antennas are the main interface between the GNSS Space Segment (the satellite constellations) and the User Segment (GNSS receivers), as they are responsible for capturing the L-band signals transmitted from space. Antennas requirements can range from gain vs. azimuth and elevation, multipath and interference rejection, or stability of the electrical phase centre, to size, shape and environmental constraints.

Typically, the antennas used in GNSS receivers are formed by a radiating element, mounted on a ground plane, followed by an amplifier and protected by a radome:

  • the radiating element is responsible for the antenna bandwidth and radiating characteristics,
  • the ground plane conditions the radiation pattern shape, foremost at low elevation angles,
  • the amplifier sets the receiver noise figure,
  • the radome affects the phase centre.

Due to the characteristics of GNSS systems, receiver antennas are typically Right-Hand Circularly Polarized[1] (RHCP) antennas, and the spacial reception pattern is near hemispherical: this configuration enables user reception of satellite signals in any azimuthal direction, and from zenith to horizon, thus maximizing satellite visibility.

Antenna configurations

Different applications may require different types of antenna design, technology and location[2]. In fact, as show in Figure 1, antennas can range from large roof-mounted antennas (e.g. for a static open sky view) to embedded antennas in receiver boards (e.g. for mobile handheld devices).

The most common types of antennas in terms of implementation of antenna elements, ground planes, are:

Figure 1: Examples of GNSS antenna types: rooftop Radome (left), embedded Patch (top-right), Choke Ring design (bottom-right).
Figure 2: View of the antennas at Galileo Control Centre in Fucino, Italy (Contents ESA).
  • Patch Antennas: Patch antennas are often used in handheld mobile devices, such as Portable Navigation Devices (PND) or smartphones, since the antenna is built as a low-profile thin microstrip (i.e. patch), suitable for small form-factor devices. Microstrip patches or aperture-coupled patches can be single frequency or dual frequency, but also broadband. Patches are not circularly polarized by nature, so they achieve circular polarization by quadrature excitation of two linearly polarized ports. The quality of the circular polarization depends largely on the feeding network and may be sensitive to fabrication issues, and the crosspolarization near the horizon tends to be high. They provide an excellent form factor (size and weight), and are used in most aviation GNSS antennas satisfying ARINC 743[3] standard.
  • Turnstile Antennas: The turnstile antenna consists of two dipoles fed in 90° phase. A horizontal turnstile antenna in free space is vertically polarized in its plane, and has opposite circular polarizations above and below. Therefore the antenna requires a ground plane for geodetic applications. When combined with a choke ring ground plane, it is a very common element in geodetic applications.
  • Helical Antennas: Helical antennas are typically built as a conducting wire around a cylindrical or conical core, in a helix form, and can be used with or without a ground plane, depending on the configuration. In GNSS receivers, the helix antennas can be used as directional antennas, with a radiation pattern along the axis of the antenna.
  • Spiral Antennas: The equiangular planar spiral is one of the prototypical "frequency-independent" antennas, so it offers excellent bandwidth. The antenna is circularly polarized by nature, although the quality of the polarization may depend on the feeding arrangement. Since the basic element radiates equally in both hemispheres, a ground plane of some kind is required.
  • Radome Antennas: As the name suggests, in this configuration the antenna elements are housed in a hemispherical-like dome (the radome). Radomes are usually added to protect the antenna when the site where it is installed demands it (e.g. in roof-mounted installations) due to weather conditions, antenna security, or wildlife concerns. Typically, hemispherical radomes are used, because they have little effect on the phase centre stability and symmetry, and non-hemispherical radomes are usually avoided, except when the shape is required by site characteristics (e.g. conical radomes for snow rejection). Antenna phase centre calibration should be performed with the radome.
  • Choke Ring Antennas: A choke ring antenna design consists in surrounding a central antenna element with several concentric conductive rings, enclosed in a protective dome. Its design is notable for the ability to reject multipath and low elevation signals (including reflections on the ground). Choke Ring antennas reflects signals that come from below, and draw surface wave signals into the choke channels, where they are cancelled or reflected away from the receiving element.
  • Resistive Plane Antennas: The resistive plane antenna uses electrical resistance (rather than frequency-tuned rings as Choke Ring antennas) to keep unwanted signals from reaching the antenna element. Signals that strike the plane lose all energy before they reach the element and cause interference. Resistive Plane antennas provide similar performances as Choke Ring antennas, but with less weight and cost.
  • Phased-Array Antennas: Phased-array antennas are mostly used for military or high-end applications, and consist of numerous antenna elements arranged in an array pattern. Each signal from an antenna in the array can be processed by introducing dynamic phase shifts, and when the outputs of the array are summed, the effective radiation pattern can be maximized in some directions and nulled in other (e.g. inserting nulls in the antenna pattern can help adjusting to jamming threats). Furthermore, beam steering techniques can be used to increase dynamically the antenna gain in a given direction, e.g. of a given satellite. This technique can be used in ground reference antennas in order to maximize the antenna gain.
  • Parabolic Antennas: Resembling popular TV and communications satellite dish antennas, parabolic antennas use a parabolic reflecting surface to direct the radio waves. The parabolic antenna is highly directive, so RF signals coming from the satellites can be received from one particular direction only. Its directive build structure and high gain make this type of antenna suitable for Ground Segment stations, such as monitoring or uplink stations, as shown in Figure 2.

Applications

An alternative distinction of GNSS antennas[4] is in terms of the envisaged application:

  • Geodetic Antennas: Survey and geodetic applications typically require fixed high-accuracy receivers and antennas, so it is common for multi-frequency / multi-constellation choke-ring antennas to be used for best performance.
  • Rover Antennas: Rover antennas are typically used in land survey, forestry, construction, and other portable or mobile applications, hence they require a trade-off between accuracy and portability. Due to the need for mobility, the antenna is usually mounted on a handheld pole, stand or tripod. In general, due to size and weight constraints, choke ring antennas are not a good solution for rover applications, so higher phase center variations are often seen in rover antennas.
  • Handheld Receiver Antennas: These antennas are found in most current smartphones and portable navigation devices, and the key design drivers are size, cost and power consumption constraints. Usually single-frequency antennas, they are available in a range of implementations such as helical or patch antennas, both passive and active (see section below for details).

Characteristics

Antennas used in GNSS receivers aim at capturing L-band signals and therefore their design should take into account signal bandwidth, centre frequency, desired response, transfer function, multipath mitigation, and electromechanical factors. Table 1 shows a few relations between antenna applications and characteristics.


Table 1: GNSS antenna applications and characteristics.
  Geodetic Rover Handheld
Frequency Bands Single to multiband Single to multiband Singleband
Bandwidth Broadband Narrow to Broadband Narrowband
Radiation Pattern Controlled Controlled Not controlled
Multipath suppression High Medium None
Sensitivity High Medium to high Low
Interference Handling High rejection Good rejection Minimal rejection
Phase centre Very important Important Not important
Dimensions Large Portable Very small
Weight Heavy Portable Lightweight
Cost High Medium Low


Antenna Power

In general, GNSS antennas do not need any electrical power to operate, and are referred to as passive antennas. Typical scenarios for passive antennas are mobile devices, where power consumption is a critical issue. However, passive antennas must connect to the receiver's front end with very low losses, since there is no amplification mechanism involved at signal reception.

In applications in which the antenna can be away from the receiver (e.g. rooftop antennas), signal amplification can be implemented in the antenna itself, and for that fact they are called active antennas. Their purpose is to amplify the received signal to compensate for potential losses in long coaxial cables, at the cost of higher power consumption (power is usually delivered from the front end through the coaxial cable itself). In this approach, a Low-Noise Amplifier (LNA) is usually added to the antenna setup, in order to ensure a low noise figure in the signals to process. An example of active antenna use is for indoor reradiating purposes, where an active antenna inside a building reradiates the signals coming from another antenna, placed outside the building.

Radiation Pattern

Figure 3: Example of a patch antenna pattern.

GNSS signals use Right Hand Circular Polarization (RHCP), but antennas are not perfect, so a RHCP antenna will pick up some Left Hand Circular Polarization (LHCP) energy as well. In radiation terms, RHCP is referred to as the co-polar component, and LHCP is referred as the cross-polar component. The typical radiation pattern coverage is around 160º, resulting in low gain for signals coming in at low elevation angles, as shown in Figure 3 for a patch antenna. This pattern aims at maximizing the gain at zenith, decreasing to near unity at an elevation angle of around 10º-15º, and to negative gains below the elevation threshold (sometimes referred to as elevation mask).

Real-world GNSS antennas experience a gain roll-off of 10 to 20 dB from broadside (90º elevation) to the horizon (0º elevation). At zenith, the ratio of the vertical electric field to the horizontal electric field response is near unity (0 dB); this ratio is referred to as the axial ratio[5] (AR). The AR tends to degrade towards lower elevations, and it can reach less than 3 to 6 dB at 10° elevation for a high-performance antenna.

Multipath

Signals sent from GNSS satellites will directly arrive at the antenna but they also may be reflected off the ground, buildings or other obstacles, arriving at the antenna multiple times and delayed in time. This phenomenon is called multipath, and since it degrades position accuracy, it should be avoided or reduced. Multipath signals can basically come from three directions: the ground, hitting the back of the antenna, the ground or an object, hitting the antenna at a low elevation, or an object, hitting the antenna at a high elevation.

In specular reflections, the reflected signal may change its polarization with respect to the original one, i.e. depending on the material and on the angle of incidence, a RHCP signal can be reflected as a LHCP signal. The multipath susceptibility of an antenna can then be quantified, with respect to the antenna’s radiation pattern characteristics, by the multipath ratio (MPR). The multipath ratio is computed as the ratio between the RHCP gain at the satellite signal incident angle with respect to the sum of the RHCP and LHCP gains at the multipath signal incident angle.

Gain roll-off towards the lower elevations helps suppressing multipath signals: however, a good AR is always a must, since gain roll-off alone is insufficient.

Phase Centre

Another important design factor for antennas is the phase centre. In fact, when a receiver determines a position solution, it is actually estimating the position of the electrical phase centre of the antenna, where the signals are captured, regardless of the distance from the antenna the receiver device really is. This electrical phase centre should not be mistaken with the physical phase centre: although the latter can be observed and is a physical constant, the first may vary, depending on the direction of the signal arrival.

Determining the phase centre is important in GNSS systems, particularly when millimeter positioning resolution is desired; nevertheless, for well-designed high-end GNSS antennas, phase centre variations in azimuth are small and in the order of few millimetres (the vertical phase offsets are typically 10 mm or less). See the articles on antenna phase centre and receiver antenna phase centre for more details.

Interference Handling

An out-of-band interferer is an RF source outside of the GNSS frequency bands, which can drive the LNA into its nonlinear range, and the LNA starts to operate as a multiplier or comb generator. RF filters can reduce the out-of-band signals by tens of dBs, which is enough in most cases. Of course, filters add insertion loss, amplitude and phase ripple, all of which degrade receiver performance. In-band interferers can be the third-order mixing products, or simply an RF source that transmits inside the GNSS bands. If these are relatively weak, the receiver will handle them; from a certain power level on, however, commercial receivers can do nothing about them.

Furthermore, antenna arrays can use beamforming techniques[6] to create nulls in the radiation pattern in the direction of a-priori known interferers – this technique is often used in military applications.

Noise and Out of Band Rejection

The signals received by the antenna are very weak. For instance, in GPS, the minimum received power is –158.5 dBW (for L1) and –164.5 dBW (for L2), for signals arriving at 5º elevation. Furthermore, the cable and the receiver elements generate noise that can affect the signal. To avoid reducing this effect, the first element following the antenna is usually a Low Noise Amplifier (LNA), so that the power of the GNSS signal is greater than the noise generated by the cable and the receiver elements.

Adding the fact that Out of Band signals need to be rejected or attenuated to prevent the saturation of the amplifiers, and that the antenna does not provide a good close Out of Band rejection, a pass band filter can be placed before the first amplifier. This operation, however, will degrade the Noise Figure, so there is a trade-off in the design of the antenna LNA between the Noise Figure and the Out of Band Rejection. Typically, the compromise is reached by distributing the filtering across the LNA in two stages.

Signal Bandwidth

Besides electrical considerations, GNSS RF section must also take into account the signal structure in terms of RF spectrum and bandwidth, and should be selected not only in accordance with the front end specifications, but also with the envisaged usage and application. Typical GPS antennas are able to process signal bandwidth of around 1% to 2% of the signal center frequency (yielding over 20 MHz bandwidth in L1). These values are able to fit most GNSS signals and therefore the limitations on the signal bandwidth is usually concentrated in the front-end block, keeping in mind that both antenna and front-end blocks contribute to this bandwidth[7].

Front end connection

The antenna signal provided to the front end is received as a low-power signal, and is typically amplified and filtered before entering the down-conversion and sampling process. In the case of the antenna being far from the receiver, for physical constraints or application necessity, special attention should be drawn to the choice of the connecting cable.


Table 3: Example of coaxial cable types and losses [dB / 100m].
  915 MHz 1.2 GHz 2.4 GHz
RG-58 54.1 69.2 105.6
RG-8X 42.0 52.8 75.8
LMR-400 12.8 15.7 22.3
LMR-600 8.2 10.2 14.4
1 5/8" LDF 2.5 3.1 4.6


Coaxial cables are built in many different ways, with different materials, with or without special shielding, and specify losses in units of power and length per frequency range - typical values are in the form of "X dB/100 m @ Y MHz". Requirements like cable length, impedance, antenna gain and power supply (for the case of active antennas) need to be taken into account to minimize signal losses. For illustrative purposes, an example of the loss ranges at stake[8] is shown in Table 3. In this example, from a signal loss point of view, the "1 5/8" LDF" cable would have less losses in the 1.2 - 1.6 GHz range of GNSS signals, and should be considered for connecting an antenna to the front end.

Related articles

References

  1. ^ wikipedia:Circular Polarization
  2. ^ wikipedia:Category:Radio frequency antenna types
  3. ^ https://www.arinc.com/cf/store/catalog_detail.cfm?item_id=329
  4. ^ GPS World 2009 Antenna Survey.
  5. ^ Kaplan, E.D. et al,"Understanding GPS: Principles and Applications", second edition, chapter 3, section 3.4.1.1.
  6. ^ A. Konovaltsev, F. Antreich, A. Hornbostel (2007), “Performance assessment of antenna array algorithms for multipath and interferers mitigation”, Proc. of 2nd Workshop on GNSS Signals & Signal Processing (GNSS SIGNALS’2007), 24-25 April 2007, Noordwijk, the Netherlands.
  7. ^ Kaplan, E.D. et al, "Understanding GPS: Principles and Applications", second edition
  8. ^ http://www.w4rp.com/ref/coax.html