If you wish to contribute or participate in the discussions about articles you are invited to contact the Editor

Regional Datums and Map Projections: Difference between revisions

From Navipedia
Jump to navigation Jump to search
(Created page with "{{Article Infobox2 |Category=Fundamentals |Title={{PAGENAME}} |Authors=J. Sanz Subirana, JM. Juan Zornoza and M. Hernandez-Pajares, University of Catalunia, Spain. |Level=Basic |...")
 
No edit summary
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{Article Infobox2
{{Article Infobox2
|Category=Fundamentals
|Category=Fundamentals
|Title={{PAGENAME}}
|Authors=J. Sanz Subirana, J.M. Juan Zornoza and M. Hernández-Pajares, Technical University of Catalonia, Spain.
|Authors=J. Sanz Subirana, JM. Juan Zornoza and M. Hernandez-Pajares, University of Catalunia, Spain.
|Level=Basic
|Level=Basic
|YearOfPublication=2011
|YearOfPublication=2011
|Title={{PAGENAME}}
}}
}}
A datum consists in a ellipsoid relative to which the latitude and longitude of points are defined, and a geoid defining the surface at zero height <ref group="footnotes">More precisely, the equipotential surface of earth's gravity field that on average coincides with mean sea level in the open oceans. Note that due to variations in gravity, the geoid undulates significantly.</ref>.Different organisations, countries or groups of countries have developed their own datums for civil and military applications.
A datum consists in an ellipsoid relative to which the latitude and longitude of points are defined, and a geoid defining the surface at zero height <ref group="footnotes">More precisely, the equipotential surface of earth's gravity field that on average coincides with mean sea level in the open oceans. Note that due to variations in gravity, the geoid undulates significantly.</ref>.Different organisations, countries or groups of countries have developed their own datums for civil and military applications.
 
 
Such ellipsoids are conventionally defined as fitting the geoid in the region of interest, without them being necessarily geocentric or to have their axes constrained to a given orientation. A valuable contribution of [[GPS General Introduction|GPS]] was to provide a Global Reference Frame, simplifying the mapping of the earth and unifying the diverse datums [Misra & Enge, 2001]<ref> [Misra and Enge, 2001] Misra, P. and Enge, P., 2001. Global Positioning System. Signals, Measurements and Performance. Ganga-Jamuna Press, Massachusetts, US.</ref>. Figure 1 illustrates the concept of Local and Global datum, and its relation the geoid.


Such ellipsoids are conventionally defined as fitting the geoid in the region of interest, without them being necessarily geocentric or to have their axes constrained to a given orientation. A valuable contribution of \acs{GPS} was to provide a Global Reference Frame, simplifying the mapping of the earth and unifying the diverse datums [Misra and Enge, 2001]<ref> [Misra and Enge, 2001] Misra, P. and Enge, P., 2001. Global Positioning System. Signals, Measurements and Performance.. Ganga-Jamuna Press, Massachusetts, US.</ref>. Figure 1 illustrates the concept of Local and Global datum, and its relation the geoid.


::[[File:Datum.png|none|thumb|400px|'''''Figure 1:''''' Global and Local geodetic datums and Geoid.]]


::[[File:Datum.png|none|thumb|400px|'''''Figure 1:''''' Global and Local geodetic datums .]]


The ellipsoidal coordinates of the datum must then be mapped into plane coordinates using a proper projection to build a map. Different projections have been defined (preserving areas, angles, distances, etc.), but all of them introduce distortions due to the mapping of a curve surface to a plane (see, for instance, [Hofmann-Wellenhof et al., 2008], chapter 8<ref> [Hofmann-Wellenhof et al., 2008] Hofmann-Wellenhof, B., Lichtenegger, H.,K. and Wasle, E., 2008. GNSS - Global Navigation Satellite Systems..Springer-Verlag, Wien, Austria.</ref>).


The ellipsoidal coordinates of the datum must then be mapped into plane coordinates using a proper projection to build a map. Different projections have been defined (preserving areas, angles, distances, etc.), but all of them introduce distortions due to the mapping of a curve surface to a plane (see, for instance, [Hofmann-Wellenhof et al., 2008]<ref> [Hofmann-Wellenhof et al., 2008] Hofmann-Wellenhof, B., Lichtenegger, H.,K. and Wasle, E., 2008. GNSS - Global Navigation Satellite Systems..Springer-Verlag, Wien, Austria.</ref>, chapter 8).


The local maps edited by the official organisms are referenced to a given datum. The coordinates expressed in a datum can be transformed into another with a 7 parameter transformation as explained in [[Transformation between Celestial and Terrestrial Frames]]. In this way, most of the commercial receivers incorporate the parameters for several official datums to map the WGS84 coordinates.
The local maps edited by the official organisms are referenced to a given datum. The coordinates expressed in a datum can be transformed into another with a 7 parameter transformation as explained in [[Transformation between Celestial and Terrestrial Frames]]. In this way, most of the commercial receivers incorporate the parameters for several official datums to map the WGS84 coordinates.
Line 29: Line 31:


[[Category:Fundamentals]]
[[Category:Fundamentals]]
[[Category:GNSS Time Reference, Coordinate Frames and Orbits]]

Latest revision as of 11:41, 23 February 2012


FundamentalsFundamentals
Title Regional Datums and Map Projections
Author(s) J. Sanz Subirana, J.M. Juan Zornoza and M. Hernández-Pajares, Technical University of Catalonia, Spain.
Level Basic
Year of Publication 2011

A datum consists in an ellipsoid relative to which the latitude and longitude of points are defined, and a geoid defining the surface at zero height [footnotes 1].Different organisations, countries or groups of countries have developed their own datums for civil and military applications.


Such ellipsoids are conventionally defined as fitting the geoid in the region of interest, without them being necessarily geocentric or to have their axes constrained to a given orientation. A valuable contribution of GPS was to provide a Global Reference Frame, simplifying the mapping of the earth and unifying the diverse datums [Misra & Enge, 2001][1]. Figure 1 illustrates the concept of Local and Global datum, and its relation the geoid.


Figure 1: Global and Local geodetic datums and Geoid.


The ellipsoidal coordinates of the datum must then be mapped into plane coordinates using a proper projection to build a map. Different projections have been defined (preserving areas, angles, distances, etc.), but all of them introduce distortions due to the mapping of a curve surface to a plane (see, for instance, [Hofmann-Wellenhof et al., 2008], chapter 8[2]).


The local maps edited by the official organisms are referenced to a given datum. The coordinates expressed in a datum can be transformed into another with a 7 parameter transformation as explained in Transformation between Celestial and Terrestrial Frames. In this way, most of the commercial receivers incorporate the parameters for several official datums to map the WGS84 coordinates.


Notes

  1. ^ More precisely, the equipotential surface of earth's gravity field that on average coincides with mean sea level in the open oceans. Note that due to variations in gravity, the geoid undulates significantly.


References

  1. ^ [Misra and Enge, 2001] Misra, P. and Enge, P., 2001. Global Positioning System. Signals, Measurements and Performance. Ganga-Jamuna Press, Massachusetts, US.
  2. ^ [Hofmann-Wellenhof et al., 2008] Hofmann-Wellenhof, B., Lichtenegger, H.,K. and Wasle, E., 2008. GNSS - Global Navigation Satellite Systems..Springer-Verlag, Wien, Austria.